b'FRACTIONALBaselineINCH Baseline DCinSpeed and FeedSquare, Corner Radius & Ball End Vc 0 .0050 0 .0156 0 .0312 0 .0625 0 .0938 0 .1200With and Without Reach Hardness (sfm)Profile 1000 RPM 764000 244872 122436 61120 40725 31833(800-1200) Fz 0.000064 0.00020 0.00040 0.00080 0.00120 0.00153PLASTICS Feed (ipm) 97.50 97.50 97.50 97.50 97.50 97.50N Polycarbonate, PVC, Polypropylene Slot 800 RPM 611200 195897 97949 48896 32580 25467(640-960) Fz 0.000064 0.00020 0.00040 0.00080 0.00120 0.00153Feed (ipm) 78.00 78.00 78.00 78.00 78.00 78.00Profile 60 RPM 45840 14692 7346 3667 2443 1910SUPER ALLOYS (48-72) Fz 0.000012 0.00004 0.00008 0.00015 0.00023 0.00029(NICKEL, COBALT,300 Bhn Feed (ipm) 1.11 1.11 1.11 1.11 1.11 1.11S IRON BASE) orInconel 601, 617, 625, 32 HRc Slot 45 RPM 34380 11019 5510 2750 1833 1433Incoloy, Monel 400 Fz 0.000012 0.00004 0.00008 0.00015 0.00023 0.00029(36-54) Feed (ipm) 0.83 0.83 0.83 0.83 0.83 0.83Profile 45 RPM 34380 11019 5510 2750 1833 1433SUPER ALLOYS Fz 0.000008 0.00003 0.00005 0.00010 0.00015 0.00019(NICKEL, COBALT,400 Bhn (36-54) Feed (ipm) 0.55 0.55 0.55 0.55 0.55 0.55S IRON BASE) orInconel 718, X-750,43 HRc 35 RPM 26740 8571 4285 2139 1425 1114Incoloy,Waspaloy,SlotHastelloy, Rene (28-42) Fz 0.000008 0.00003 0.00005 0.00010 0.00015 0.00019Feed (ipm) 0.43 0.43 0.43 0.43 0.43 0.43Profile 160 RPM 122240 39179 19590 9779 6516 5093TITANIUM ALLOYS (128-192) Fz 0.000014 0.00004 0.00008 0.00017 0.00025 0.00033Pure Titanium, 350 Bhn Feed (ipm) 3.32 3.32 3.32 3.32 3.32 3.32S Ti6Al4V, orTi6Al2Sn4Zr2Mo, 38 HRc Slot 130 RPM 99320 31833 15917 7946 5294 4138Ti4Al4Mo2Sn0.5Si Fz 0.000014 0.00004 0.00008 0.00017 0.00025 0.00033(104-156) Feed (ipm) 2.70 2.70 2.70 2.70 2.70 2.70TITANIUM ALLOYS Profile 60 RPM 45840 14692 7346 3667 2443 1910(DIFFICULT) Fz 0.000010 0.00003 0.00006 0.00012 0.00018 0.00023Ti10Al2Fe3Al, 440 Bhn (48-72) Feed (ipm) 0.88 0.88 0.88 0.88 0.88 0.88S Ti5Al5V5Mo3Cr,orTi7Al4Mo,47 HRc 45 RPM 34380 11019 5510 2750 1833 1433Ti3Al8V6Cr4Zr4Mo,SlotTi6Al6V6Sn, (36-54) Fz 0.000010 0.00003 0.00006 0.00012 0.00018 0.00023Ti15V3 Cr3Sn3Al Feed (ipm) 0.66 0.66 0.66 0.66 0.66 0.66Profile 175 RPM 133700 42853 21426 10696 7127 5571(140-210) Fz 0.000016 0.00005 0.00010 0.00020 0.00030 0.00038TOOL STEELS375 Bhn Feed (ipm) 4.28 4.28 4.28 4.28 4.28 4.28H A2, D2, H13, L2, M2, orP20, S7, T15, W2 40 HRc Slot 140 RPM 106960 34282 17141 8557 5701 4457(112-168) Fz 0.000016 0.00005 0.00010 0.00020 0.00030 0.00038Feed (ipm) 3.42 3.42 3.42 3.42 3.42 3.42Note:Bhn (Brinell)HRc (Rockwell C) when recommended speed exceeds your capability, use maximum available and recalculate ipm rpm = Vc x 3.82 / DC ipm = Fz x No. of flutes x rpm reduce speed and feed for materials harder than listed reduce feed and Ae when finish milling (.02 x D 1maximum) refer to the KYOCERA SGS Tool Wizard or sgsmicrotools.com for detailed technical charts by seriesEND MILLS END MILLS 79www.sgsmicrotools.com'