b'FRACTIONALM4 M4CR1 .5xD30 POS12 4LFAPMXM4M4CR DCON New Expanded Tools1 .5xD DC TOLERANCES(inch)FRACTIONAL SERIES RE .005.120DIAMETERDC=+0.000/0.001continued inch EDP NO. DCON = h 6CUTTING SHANK LENGTH OVERALL CORNER RE=+0.0000 / 0.0005DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) 0.090 1/8 0.135 1-1/2 0.010 09062 09202 STEELS0.090 1/8 0.135 1-1/2 0.015 09064 09204 STAINLESS STEELS0.090 1/8 0.135 1-1/2 0.020 09066 092060.093 1/8 0.140 1-1/200435 02429 CAST IRON0.095 1/8 0.143 1-1/200436 02430 HIGH TEMP ALLOYS0.095 1/8 0.143 1-1/2 0.005 09068 09208 TITANIUM0.095 1/8 0.143 1-1/2 0.010 09070 09210HARDENED STEELS0.095 1/8 0.143 1-1/2 0.015 09072 092120.095 1/8 0.143 1-1/2 0.020 09074 09214 NON-FERROUS0.100 1/8 0.150 1-1/200437 02431 PLASTICS/COMPOSITES0.100 1/8 0.150 1-1/2 0.005 09076 092160.100 1/8 0.150 1-1/2 0.010 09078 092180.100 1/8 0.150 1-1/2 0.015 09080 092200.100 1/8 0.150 1-1/2 0.020 09082 092220.100 1/8 0.150 1-1/2 0.030 09084 092240.105 1/8 0.158 1-1/200438 024320.105 1/8 0.158 1-1/2 0.005 09086 092260.105 1/8 0.158 1-1/2 0.010 09088 092280.105 1/8 0.158 1-1/2 0.015 09090 092300.105 1/8 0.158 1-1/2 0.020 09092 092320.105 1/8 0.158 1-1/2 0.030 09094 092340.110 1/8 0.165 1-1/200439 024330.110 1/8 0.165 1-1/2 0.005 09096 092360.110 1/8 0.165 1-1/2 0.010 09098 092380.110 1/8 0.165 1-1/2 0.015 09100 092400.110 1/8 0.165 1-1/2 0.020 09102 092420.110 1/8 0.165 1-1/2 0.030 09104 092440.115 1/8 0.173 1-1/200440 024340.115 1/8 0.173 1-1/2 0.005 09106 092460.115 1/8 0.173 1-1/2 0.010 09108 092480.115 1/8 0.173 1-1/2 0.015 09110 092500.115 1/8 0.173 1-1/2 0.020 09112 092520.115 1/8 0.173 1-1/2 0.030 09114 092540.120 1/8 0.180 1-1/200441 02435continued on next page46 END MILLS END MILLSwww.sgsmicrotools.com'