b'FRACTIONALM3M3CR1 .5xD8xD Overall Reach30 POS15 3LFAPMX LUM3M3CR1 .5xDDCON8xD DC DN TOLERANCES(inch)FRACTIONAL SERIES RE .010.120DIAMETERDC=+0.000/0.001continued inch EDP NO. DCON = h 6CUTTING SHANK LENGTH NECKOVERALL CORNERRE=+0.0000 / 0.0005DIAMETER DIAMETEROF CUTREACHDIAMETERLENGTH RADIUSUNCOATEDTI-NAMITE-A DC DCON APMX LU DN LF RE (AlTiN) 0.078 1/8 0.117 0.624 0.073 2-1/209720 03579 STEELS0.080 1/8 0.120 0.640 0.075 2-1/209727 03580 STAINLESS STEELS0.080 1/8 0.120 0.640 0.075 2-1/2 0.005 08840 089420.080 1/8 0.120 0.640 0.075 2-1/2 0.010 08843 08945 CAST IRON0.080 1/8 0.120 0.640 0.075 2-1/2 0.015 08846 08948 HIGH TEMP ALLOYS0.085 1/8 0.128 0.680 0.079 2-1/209734 03581 TITANIUM0.090 1/8 0.135 0.720 0.084 2-1/209741 03582HARDENED STEELS0.090 1/8 0.135 0.720 0.084 2-1/2 0.005 08849 089510.090 1/8 0.135 0.720 0.084 2-1/2 0.010 08852 08954 NON-FERROUS0.090 1/8 0.135 0.720 0.084 2-1/2 0.015 08855 08957 PLASTICS/COMPOSITES0.093 1/8 0.140 0.744 0.087 2-1/209748 035830.095 1/8 0.143 0.760 0.089 2-1/209755 035840.100 1/8 0.150 0.800 0.094 2-1/2 09762 035850.100 1/8 0.150 0.800 0.094 2-1/2 0.005 08858 089600.100 1/8 0.150 0.800 0.094 2-1/2 0.010 08861 089630.100 1/8 0.150 0.800 0.094 2-1/2 0.015 08864 089660.110 1/8 0.165 0.880 0.103 2-1/2 09769 035860.110 1/8 0.165 0.880 0.103 2-1/2 0.005 08867 089690.110 1/8 0.165 0.880 0.103 2-1/2 0.010 08870 089720.110 1/8 0.165 0.880 0.103 2-1/2 0.015 08873 089750.115 1/8 0.173 0.920 0.108 2-1/2 09776 035870.120 1/8 0.180 0.960 0.112 2-1/2 09783 035880.120 1/8 0.180 0.960 0.112 2-1/2 0.005 08876 089780.120 1/8 0.180 0.960 0.112 2-1/2 0.010 08879 089810.120 1/8 0.180 0.960 0.112 2-1/2 0.015 08882 0898432 END MILLS END MILLSwww.sgsmicrotools.com'