b'FRACTIONAL & METRIC2 Flute External Coolant Standard & Extended Length118 1302OALLCFNew Expanded ToolsM105 DCON TOLERANCES(inch)DC .125DIAMETERFRACTIONAL & METRIC SERIES DC= +.0000/+.0003continued inch & mm EDP NO. DCON =h 6CUTTINGDECIMAL SHANKFLUTEOVERALL POINTDIAMETEREQUIV.DIAMETERLENGTH LENGTH ANGLEUNCOATEDTI-NAMITE-A DC DCON LCF OAL (AlTiN)TOLERANCES(mm)#83 0.0120 1/8 0.225 1-1/2 118 07268 07100 0,13,0DIAMETER#83 0.0120 1/8 0.280 1-1/2 118 07269 07101 DC= +0,000/+0,008#82 0.0125 1/8 0.225 1-1/2 118 07270 07102 DCON =h 6#82 0.0125 1/8 0.280 1-1/2 118 07271 07103#81 0.0130 1/8 0.225 1-1/2 118 07272 07104 STEELS#81 0.0130 1/8 0.280 1-1/2 118 07273 07105#80 0.0135 1/8 0.225 1-1/2 130 07274 07106 STAINLESS STEELS#80 0.0135 1/8 0.280 1-1/2 130 07275 07107 CAST IRON0,35mm 0.0138 1/8 0.225 1-1/2 130 07118 07122 HIGH TEMP ALLOYS0,35mm 0.0138 1/8 0.280 1-1/2 130 07119 07123TITANIUM#79 0.0145 1/8 0.225 1-1/2 130 07278 07110#79 0.0145 1/8 0.280 1-1/2 130 07279 07111 NON-FERROUS1/64 0.0156 1/8 0.250 1-1/2 130 07280 07112 HARDENED STEELS1/64 0.0156 1/8 0.295 1-1/2 130 07281 071130,4mm 0.0157 1/8 0.250 1-1/2 130 07148 072330,4mm 0.0157 1/8 0.295 1-1/2 130 07232 07234#78 0.0160 1/8 0.250 1-1/2 130 07284 07116#78 0.0160 1/8 0.295 1-1/2 130 07285 071170,45mm 0.0177 1/8 0.250 1-1/2 130 07137 071430,45mm 0.0177 1/8 0.295 1-1/2 130 07140 07145#77 0.0180 1/8 0.250 1-1/2 130 07288 07120#77 0.0180 1/8 0.295 1-1/2 130 07289 071210,5mm 0.0197 1/8 0.260 1-1/2 130 07257 072670,5mm 0.0197 1/8 0.310 1-1/2 130 07266 07276#76 0.0200 1/8 0.260 1-1/2 130 07292 07124#76 0.0200 1/8 0.310 1-1/2 130 07293 07125#75 0.0210 1/8 0.310 1-1/2 130 07294 071260,55mm 0.0217 1/8 0.340 1-1/2 130 07235 07256#74 0.0225 1/8 0.340 1-1/2 130 07296 071280,6mm 0.0236 1/8 0.340 1-1/2 130 07283 07286#73 0.0240 1/8 0.340 1-1/2 130 07298 07130#72 0.0250 1/8 0.340 1-1/2 130 07299 071310,65mm 0.0256 1/8 0.340 1-1/2 130 07277 07282#71 0.0260 1/8 0.340 1-1/2 130 07301 07133continued on next page94 DRILLS DRILLSwww.sgsmicrotools.com'