b'FRACTIONALSeries M032ApSeries Ae Ae DCinM032 VcFractional Hardness Ae x DC Ap x DC (sfm) 1/32 5/64 7/64Profile 335 RPM 40950 16380 11700 0.251 (268-402) Fz 0.00008 0.00020 0.00028Feed (ipm) 9.9 9.9 9.9STAINLESS STEELS275 Bhn Slot 245 RPM 29949 11980 8557M (DIFFICULT) or 1.5 Fz 0.00007 0.00017 0.00023304, 304L, 316, 316L28 HRc (196-294) Feed (ipm) 6.0 6.0 6.0Finish 605 RPM 73955 29582 21130 .02 1 (484-726) Fz 0.00012 0.00031 0.00043Feed (ipm) 27.5 27.5 27.5Profile 310 RPM 37894 15158 10827 0.251 (248-372) Fz 0.00008 0.00020 0.00028Feed (ipm) 9.0 9.0 9.0STAINLESS STEELS 325 Bhn Slot 225 RPM 27504 11002 7858M (PH)or 1.5 Fz 0.00007 0.00017 0.0002313-8 PH, 15-5 PH, 35 HRc (180-270)17-4 PH, Custom 450 Feed (ipm) 5.5 5.5 5.5Finish 555 RPM 67843 27137 19384 .02 1 (444-666) Fz 0.00013 0.00031 0.00044Feed (ipm) 25.5 25.5 25.5Profile 200 RPM 24448 9779 6985 0.51.5 (160-240) Fz 0.00007 0.00017 0.00024SUPER ALLOYS Feed (ipm) 5.1 5.1 5.1(NICKEL, COBALT,400 Bhn Slot 145 RPM 17725 7090 5064S IRON BASE) or 11 Fz 0.00006 0.00015 0.00021Inconel 718, X-750, 43 HRc (116-174)Incoloy, Waspaloy,Feed (ipm) 3.2 3.2 3.2Hastelloy, ReneFinish 360 RPM 44006 17603 12573 .02 1 (288-432) Fz 0.00011 0.00027 0.00038Feed (ipm) 14.5 14.5 14.5Profile 245 RPM 29949 11980 8557 0.51.5 (196-294) Fz 0.00007 0.00018 0.00025Feed (ipm) 6.3 6.3 6.3TITANIUM ALLOYS 180 RPM 22003 8801 6287Pure Titanium, 350 Bhn SlotS Ti6Al4V, or 11 Fz 0.00006 0.00015 0.00021Ti6Al2Sn4Zr2Mo,38 HRc (144-216) Feed (ipm) 3.9 3.9 3.9Ti4Al4Mo2Sn0.5SiFinish 440 RPM 53786 21514 15367 .02 1 (352-528) Fz 0.00011 0.00028 0.00039Feed (ipm) 18.0 18.0 18.0Bhn (Brinell)HRc (Rockwell C)rpm = Vc x 3.82 / DCipm = Fz x 3 x rpm (Fz x 3 x max available rpm when recommendation exceeds machine limit)ramp up to 5 degrees using slotting speed and feed rates.Do not plunge.reduce speed and feed for materials harder than listed refer to the KYOCERA SGS Tool Wizard for complete technical information (www.kyocera-sgstool.com) 86 END MILLS END MILLSwww.sgsmicrotools.com'