b'FRACTIONALM4M4CR3xD30 POS15 4LFAPMXTOLERANCES(inch) DC DCON M4M4CR3xD.005.120DIAMETER RE FRACTIONAL SERIESDC=+0.000/0.001DCON = h 6 inch EDP NO. continuedRE=+0.0000 / 0.0005 CUTTING SHANK LENGTH OVERALL CORNERDIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) STEELS 0.095 1/8 0.285 1-1/200578 02498STAINLESS STEELS 0.095 1/8 0.285 1-1/2 0.005 09069 092090.095 1/8 0.285 1-1/2 0.010 09071 09211CAST IRON 0.095 1/8 0.285 1-1/2 0.015 09073 09213HIGH TEMP ALLOYS 0.095 1/8 0.285 1-1/2 0.020 09075 09215TITANIUM 0.100 1/8 0.300 1-1/200579 024990.100 1/8 0.300 1-1/2 0.005 09077 09217HARDENED STEELS0.100 1/8 0.300 1-1/2 0.010 09079 09219NON-FERROUS 0.100 1/8 0.300 1-1/2 0.015 09081 09221PLASTICS/COMPOSITES 0.100 1/8 0.300 1-1/2 0.020 09083 092230.100 1/8 0.300 1-1/2 0.030 09085 092250.105 1/8 0.315 1-1/200580 025000.105 1/8 0.315 1-1/2 0.005 09087 092270.105 1/8 0.315 1-1/2 0.010 09089 092290.105 1/8 0.315 1-1/2 0.015 09091 092310.105 1/8 0.315 1-1/2 0.020 09093 092330.105 1/8 0.315 1-1/2 0.030 09095 092350.110 1/8 0.330 1-1/200581 025010.110 1/8 0.330 1-1/2 0.005 09097 092370.110 1/8 0.330 1-1/2 0.010 09099 092390.110 1/8 0.330 1-1/2 0.015 09101 092410.110 1/8 0.330 1-1/2 0.020 09103 092430.110 1/8 0.330 1-1/2 0.030 09105 092450.115 1/8 0.345 1-1/200582 025020.115 1/8 0.345 1-1/2 0.005 09107 092470.115 1/8 0.345 1-1/2 0.010 09109 092490.115 1/8 0.345 1-1/2 0.015 09111 092510.115 1/8 0.345 1-1/2 0.020 09113 092530.115 1/8 0.345 1-1/2 0.030 09115 092550.120 1/8 0.360 1-1/200583 025030.120 1/8 0.360 1-1/2 0.005 09117 092570.120 1/8 0.360 1-1/2 0.010 09119 092590.120 1/8 0.360 1-1/2 0.015 09121 092610.120 1/8 0.360 1-1/2 0.020 09123 092630.120 1/8 0.360 1-1/2 0.030 09125 09265END MILLS END MILLS 69www.sgsmicrotools.com'