b'FRACTIONALM2M2CR3xD30 POS15 2LFAPMXDCON M2M2CRTOLERANCES(inch) DC 3xD.004.120DIAMETER RE FRACTIONAL SERIESDC=+0.000/0.001DCON = h 6 inch EDP NO. continuedRE=+0.0000/0.0005 CUTTING SHANK LENGTH OVERALL CORNER DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) STEELS 0.093 1/8 0.279 1-1/200506 02463STAINLESS STEELS 0.095 1/8 0.285 1-1/200507 024640.095 1/8 0.285 1-1/2 0.005 08584 08725CAST IRON 0.095 1/8 0.285 1-1/2 0.010 08586 08727HIGH TEMP ALLOYS 0.095 1/8 0.285 1-1/2 0.015 08588 08729TITANIUM 0.095 1/8 0.285 1-1/2 0.020 08590 087310.100 1/8 0.300 1-1/200508 02465HARDENED STEELS0.100 1/8 0.300 1-1/2 0.005 08592 08733NON-FERROUS 0.100 1/8 0.300 1-1/2 0.010 08594 08735PLASTICS/COMPOSITES 0.100 1/8 0.300 1-1/2 0.015 08596 087370.100 1/8 0.300 1-1/2 0.020 08598 087390.100 1/8 0.300 1-1/2 0.030 08600 087410.105 1/8 0.315 1-1/200509 024660.105 1/8 0.315 1-1/2 0.005 08602 087430.105 1/8 0.315 1-1/2 0.010 08604 087450.105 1/8 0.315 1-1/2 0.015 08606 087470.105 1/8 0.315 1-1/2 0.020 08608 087490.105 1/8 0.315 1-1/2 0.030 08610 087510.110 1/8 0.330 1-1/200878 024670.110 1/8 0.330 1-1/2 0.005 08612 087530.110 1/8 0.330 1-1/2 0.010 08614 087550.110 1/8 0.330 1-1/2 0.015 08616 087570.110 1/8 0.330 1-1/2 0.020 08618 087590.110 1/8 0.330 1-1/2 0.030 08620 087610.115 1/8 0.345 1-1/200511 024680.115 1/8 0.345 1-1/2 0.005 08622 087630.115 1/8 0.345 1-1/2 0.010 08624 087650.115 1/8 0.345 1-1/2 0.015 08626 087670.115 1/8 0.345 1-1/2 0.020 08628 087690.115 1/8 0.345 1-1/2 0.030 08630 087710.120 1/8 0.360 1-1/200512 024690.120 1/8 0.360 1-1/2 0.005 08632 087730.120 1/8 0.360 1-1/2 0.010 08634 087750.120 1/8 0.360 1-1/2 0.015 08636 087770.120 1/8 0.360 1-1/2 0.020 08638 087790.120 1/8 0.360 1-1/2 0.030 08640 08781END MILLS END MILLS 17www.sgsmicrotools.com'