b'FRACTIONALM2M2CR3xD30 POS12 2LFAPMXM2M2CRDCON New Expanded Tools3xD DC TOLERANCES(inch)FRACTIONAL SERIES RE .004.120DIAMETERDC=+0.000/0.001continued inch EDP NO. DCON = h 6CUTTING SHANK LENGTH OVERALL CORNERRE=+0.0000/0.0005DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) 0.058 1/8 0.174 1-1/200496 02453 STEELS0.059 1/8 0.177 1-1/200865 02454 STAINLESS STEELS0.060 1/8 0.180 1-1/200498 024550.060 1/8 0.180 1-1/2 0.005 08534 08675 CAST IRON0.060 1/8 0.180 1-1/2 0.010 08536 08677 HIGH TEMP ALLOYS0.060 1/8 0.180 1-1/2 0.015 08538 08679 TITANIUM0.062 1/8 0.186 1-1/200499 02456HARDENED STEELS0.065 1/8 0.195 1-1/200500 024570.065 1/8 0.195 1-1/2 0.005 08540 08681 NON-FERROUS0.065 1/8 0.195 1-1/2 0.010 08542 08683 PLASTICS/COMPOSITES0.065 1/8 0.195 1-1/2 0.015 08544 086850.070 1/8 0.210 1-1/200501 024580.070 1/8 0.210 1-1/2 0.005 08546 086870.070 1/8 0.210 1-1/2 0.010 08548 086890.070 1/8 0.210 1-1/2 0.015 08550 086910.075 1/8 0.225 1-1/204007 040030.075 1/8 0.225 1-1/2 0.005 08552 086930.075 1/8 0.225 1-1/2 0.010 08554 086950.075 1/8 0.225 1-1/2 0.015 08556 086970.075 1/8 0.225 1-1/2 0.020 08558 086990.078 1/8 0.234 1-1/200870 024590.080 1/8 0.240 1-1/200503 024600.080 1/8 0.240 1-1/2 0.005 08560 087010.080 1/8 0.240 1-1/2 0.010 08562 087030.080 1/8 0.240 1-1/2 0.015 08564 087050.080 1/8 0.240 1-1/2 0.020 08566 087070.085 1/8 0.255 1-1/200504 024610.085 1/8 0.255 1-1/2 0.005 08568 087090.085 1/8 0.255 1-1/2 0.010 08570 087110.085 1/8 0.255 1-1/2 0.015 08572 087130.085 1/8 0.255 1-1/2 0.020 08574 087150.090 1/8 0.270 1-1/200505 024620.090 1/8 0.270 1-1/2 0.005 08576 087170.090 1/8 0.270 1-1/2 0.010 08578 087190.090 1/8 0.270 1-1/2 0.015 08580 087210.090 1/8 0.270 1-1/2 0.020 08582 08723continued on next page16 END MILLS END MILLSwww.sgsmicrotools.com'