b'FRACTIONALM2M2CR1 .5xD30 POS15 2LFAPMXDCON M2M2CRTOLERANCES(inch) DC 1 .5xD.004.120DIAMETER RE FRACTIONAL SERIESDC=+0.000/0.001DCON = h 6 inch EDP NO. continuedRE=+0.0000/0.0005 CUTTING SHANK LENGTH OVERALL CORNER DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) STEELS 0.095 1/8 0.143 1-1/200365 02396STAINLESS STEELS 0.095 1/8 0.143 1-1/2 0.005 08583 087240.095 1/8 0.143 1-1/2 0.010 08585 08726CAST IRON 0.095 1/8 0.143 1-1/2 0.015 08587 08728HIGH TEMP ALLOYS 0.095 1/8 0.143 1-1/2 0.020 08589 08730TITANIUM 0.100 1/8 0.150 1-1/200366 023970.100 1/8 0.150 1-1/2 0.005 08591 08732HARDENED STEELS0.100 1/8 0.150 1-1/2 0.010 08593 08734NON-FERROUS 0.100 1/8 0.150 1-1/2 0.015 08595 08736PLASTICS/COMPOSITES 0.100 1/8 0.150 1-1/2 0.020 08597 087380.100 1/8 0.150 1-1/2 0.030 08599 087400.105 1/8 0.158 1-1/200367 023980.105 1/8 0.158 1-1/2 0.005 08601 087420.105 1/8 0.158 1-1/2 0.010 08603 087440.105 1/8 0.158 1-1/2 0.015 08605 087460.105 1/8 0.158 1-1/2 0.020 08607 087480.105 1/8 0.158 1-1/2 0.030 08609 087500.110 1/8 0.165 1-1/200368 023990.110 1/8 0.165 1-1/2 0.005 08611 087520.110 1/8 0.165 1-1/2 0.010 08613 087540.110 1/8 0.165 1-1/2 0.015 08615 087560.110 1/8 0.165 1-1/2 0.020 08617 087580.110 1/8 0.165 1-1/2 0.030 08619 087600.115 1/8 0.173 1-1/200369 024000.115 1/8 0.173 1-1/2 0.005 08621 087620.115 1/8 0.173 1-1/2 0.010 08623 087640.115 1/8 0.173 1-1/2 0.015 08625 087660.115 1/8 0.173 1-1/2 0.020 08627 087680.115 1/8 0.173 1-1/2 0.030 08629 087700.120 1/8 0.180 1-1/200370 024010.120 1/8 0.180 1-1/2 0.005 08631 087720.120 1/8 0.180 1-1/2 0.010 08633 087740.120 1/8 0.180 1-1/2 0.015 08635 087760.120 1/8 0.180 1-1/2 0.020 08637 087780.120 1/8 0.180 1-1/2 0.030 08639 08780END MILLS END MILLS 13www.sgsmicrotools.com'