b'FRACTIONALM2M2CR1 .5xD30 POS12 2LFAPMXM2M2CR DCON New Expanded Tools1 .5xD DC TOLERANCES(inch)FRACTIONAL SERIES RE .004.120DIAMETERDC=+0.000/0.001continued inch EDP NO. DCON = h 6CUTTING SHANK LENGTH OVERALL CORNERRE=+0.0000/0.0005DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) 0.059 1/8 0.089 1-1/200355 02386 STEELS0.060 1/8 0.090 1-1/200356 02387STAINLESS STEELS0.060 1/8 0.090 1-1/2 0.005 08533 086740.060 1/8 0.090 1-1/2 0.010 08535 08676 CAST IRON0.060 1/8 0.090 1-1/2 0.015 08537 08678 HIGH TEMP ALLOYS0.062 1/8 0.093 1-1/200357 02388 TITANIUM0.065 1/8 0.098 1-1/200358 023890.065 1/8 0.098 1-1/2 0.005 08539 08680 HARDENED STEELS0.065 1/8 0.098 1-1/2 0.010 08541 08682 NON-FERROUS0.065 1/8 0.098 1-1/2 0.015 08543 08684 PLASTICS/COMPOSITES0.070 1/8 0.105 1-1/200359 023900.070 1/8 0.105 1-1/2 0.005 08545 086860.070 1/8 0.105 1-1/2 0.010 08547 086880.070 1/8 0.105 1-1/2 0.015 08549 086900.075 1/8 0.112 1-1/204006 040020.075 1/8 0.113 1-1/2 0.005 08551 086920.075 1/8 0.113 1-1/2 0.010 08553 086940.075 1/8 0.113 1-1/2 0.015 08555 086960.075 1/8 0.113 1-1/2 0.020 08557 086980.078 1/8 0.117 1-1/200360 023910.080 1/8 0.120 1-1/200361 023920.080 1/8 0.120 1-1/2 0.005 08559 087000.080 1/8 0.120 1-1/2 0.010 08561 087020.080 1/8 0.120 1-1/2 0.015 08563 087040.080 1/8 0.120 1-1/2 0.020 08565 087060.085 1/8 0.128 1-1/200362 023930.085 1/8 0.128 1-1/2 0.005 08567 087080.085 1/8 0.128 1-1/2 0.010 08569 087100.085 1/8 0.128 1-1/2 0.015 08571 087120.085 1/8 0.128 1-1/2 0.020 08573 087140.090 1/8 0.135 1-1/200363 023940.090 1/8 0.135 1-1/2 0.005 08575 087160.090 1/8 0.135 1-1/2 0.010 08577 087180.090 1/8 0.135 1-1/2 0.015 08579 087200.090 1/8 0.135 1-1/2 0.020 08581 087220.093 1/8 0.140 1-1/200364 02395continued on next page12 END MILLS END MILLSwww.sgsmicrotools.com'