b'FRACTIONALM2M2CR1 .5xD30 POS15 2LFAPMXDCON M2M2CRTOLERANCES(inch) DC 1 .5xD.004.120DIAMETER RE FRACTIONAL SERIESDC=+0.000/0.001DCON = h 6 inch EDP NO. continuedRE=+0.0000/0.0005 CUTTING SHANK LENGTH OVERALL CORNER DIAMETER DIAMETEROF CUTLENGTH RADIUSUNCOATEDTI-NAMITE-ADC DCON APMX LF RE (AlTiN) STEELS 0.035 1/8 0.053 1-1/200331 02231STAINLESS STEELS 0.035 1/8 0.053 1-1/2 0.005 08509 086500.035 1/8 0.053 1-1/2 0.010 08511 08652CAST IRON 0.036 1/8 0.054 1-1/200332 02232HIGH TEMP ALLOYS 0.037 1/8 0.056 1-1/200333 02233TITANIUM 0.038 1/8 0.057 1-1/200334 022340.039 1/8 0.059 1-1/200335 02235HARDENED STEELS0.040 1/8 0.060 1-1/200336 02236NON-FERROUS 0.040 1/8 0.060 1-1/2 0.005 08513 08654PLASTICS/COMPOSITES 0.040 1/8 0.060 1-1/2 0.010 08515 086560.041 1/8 0.062 1-1/200337 023680.042 1/8 0.063 1-1/200338 023690.043 1/8 0.065 1-1/200339 023700.044 1/8 0.066 1-1/200340 023710.045 1/8 0.068 1-1/200341 023720.045 1/8 0.068 1-1/2 0.005 08517 086580.045 1/8 0.068 1-1/2 0.010 08519 086600.046 1/8 0.069 1-1/200342 023730.047 1/8 0.071 1-1/200343 023740.048 1/8 0.072 1-1/200344 023750.049 1/8 0.074 1-1/200345 023760.050 1/8 0.075 1-1/200346 023770.050 1/8 0.075 1-1/2 0.005 08521 086620.050 1/8 0.075 1-1/2 0.010 08523 086640.050 1/8 0.075 1-1/2 0.015 08525 086660.051 1/8 0.077 1-1/200347 023780.052 1/8 0.078 1-1/200348 023790.053 1/8 0.080 1-1/200349 023800.054 1/8 0.081 1-1/200350 023810.055 1/8 0.083 1-1/200351 023820.055 1/8 0.083 1-1/2 0.005 08527 086680.055 1/8 0.083 1-1/2 0.010 08529 086700.055 1/8 0.083 1-1/2 0.015 08531 086720.056 1/8 0.084 1-1/200352 023830.057 1/8 0.086 1-1/200353 023840.058 1/8 0.087 1-1/200354 02385continued on next pageEND MILLS END MILLS 11www.sgsmicrotools.com'