b'METRICSeries M032ApSeries Ae Ae DCmmM032 VcMetric Hardness Ae x DC Ap x DC (m/min)1 2 3Profile 102 RPM 32475 16238 10825 0.251 (82-123) Fz 0.0026 0.0052 0.0077Feed (ipm) 251 251 251STAINLESS STEELS275 Bhn Slot 75 RPM 23751 11875 7917M (DIFFICULT) or 1.5 Fz 0.0021 0.0043 0.0064304, 304L, 316, 316L28 HRc (60-90) Feed (ipm) 152 152 152Finish 184 RPM 58650 29325 19550 .02 1 (148-221) Fz 0.0040 0.0079 0.0119Feed (ipm) 699 699 699Profile 94 RPM 30052 15026 10017 0.251 (76-113) Fz 0.0025 0.0051 0.0076Feed (ipm) 229 229 229STAINLESS STEELS 325 Bhn Slot 69 RPM 21812 10906 7271M (PH)or 1.5 Fz 0.0021 0.0043 0.006413-8 PH, 15-5 PH, 35 HRc (55-82)17-4 PH, Custom 450 Feed (ipm) 140 140 140Finish 169 RPM 53803 26901 17934 .02 1 (135-203) Fz 0.0040 0.0080 0.0120Feed (ipm) 648 648 648Profile 61 RPM 19388 9694 6463 0.51.5 (49-73) Fz 0.0022 0.0045 0.0067SUPER ALLOYS Feed (ipm) 130 130 130(NICKEL, COBALT,400 Bhn Slot 44 RPM 14057 7028 4686S IRON BASE) or 11 Fz 0.0019 0.0039 0.0058Inconel 718, X-750, 43 HRc (35-53)Incoloy, Waspaloy,Feed (ipm) 81 81 81Hastelloy, ReneFinish 110 RPM 34899 17449 11633 .02 1 (88-132) Fz 0.0035 0.0070 0.0106Feed (ipm) 368 368 368Profile 75 RPM 23751 11875 7917 0.51.5 (60-90) Fz 0.0022 0.0045 0.0067Feed (ipm) 160 160 160TITANIUM ALLOYS 55 RPM 17449 8725 5816Pure Titanium, 350 Bhn SlotS Ti6Al4V, or 11 Fz 0.0019 0.0038 0.0057Ti6Al2Sn4Zr2Mo,38 HRc (44-66) Feed (ipm) 99 99 99Ti4Al4Mo2Sn0.5SiFinish 134 RPM 42654 21327 14218 .02 1 (107-161) Fz 0.0036 0.0071 0.0107Feed (ipm) 457 457 457Bhn (Brinell)HRc (Rockwell C)rpm = (Vc x 1000) / (DC x 3.14)mm/min = Fz x 3 x rpm(Fz x 3 x max available rpm when recommendation exceeds machine limit)reduce speed and feed for materials harder than listed refer to the KYOCERA SGS Tool Wizard for complete technical information (www.kyocera-sgstool.com) 106 END MILLS END MILLSwww.sgsmicrotools.com'